Suggestions for oven temperature settings and baking time vary. Diameter increased to .311 inch with one coat of powder. I find It doesn’t take much paint…a thin, even coat is best. He is married, with four sons and daughters-law and 9-and-counting grandkids. The bullet’s crimp groove remained deep enough to apply a good crimp that kept the bullets in place during heavy recoil in a .357 Magnum revolver. A borescope showed no streaks of lead in the bore.

All that is really required is powder, a plastic container, protective gloves and a mask. There are two main causes for this issue: an undersize bullet bouncing its way down the barrel and stripping off lead, or a bullet cast from an alloy too soft for the velocity.

Gas checks were applied to some and left off the others for future testing. Cast bullets are easily made at home or are inexpensive to purchase in quantity, are economical, and don’t require an elaborate set-up or supply chain to produce. You’ll need to try to spread the bullets out in the tray – you do not want them touching or sticking to each other if at all possible. A toaster oven is the most common heat source for melting powder onto bullets. Loads of Bacon enjoys bullet casting, reloading, hunting, and most other outdoors activities. This site uses cookies to improve your experience.

A toaster oven was purchased for $20 at a local store, with a coupon and a discount. One last advantage (at least the way I see it) – you’ll have “real purty” cartridges in your magazine or in your belt loops. Fired with 12.0 grains of Unique, the velocity and size of five-shot groups was pretty much the same whether the bullets were lubed and sized or powder coated and sized. The initial 60 second cooling -off period is an important step – I’ve learned this the hard way. Powder can be applied to bullets by several methods, from complicated to quick. Some guys will put small plastic Airsoft balls in the shaker container with the bullets to add to the static electricity, or even use some type of spray gun to spray the powder onto the bullets…I’ve never found these processes necessary. Leading is an aggravation better avoided than addressed. All that vigorous shaking did for me was knock the powder off bullets. You will have to experiment to find the right shaker container, the amount of paint needed, etc.

Transferring powder-coated bullets onto a pan to heat the bullets and melt the powder is a delicate process. …here is a bottle each of red and yellow from Harbor Freight. It is coating a metal part with powdered paint using heat, and is popular in industrial applications. They are harder than swaged bullets and can be driven to higher velocities, resulting in a much better bullet for most applications. A quick explanation…all lead bullets are not necessarily cast bullets. This electrostatic attraction adheres powder to bullets. Trying out the Eastwood Full Gloss Clear, Mirror Black, Orange, Bright Yellow, and Single Stage Reflective Chrome powder coat on my cast bullets. 11FS powder. After shaking bullets. Two coats of Harbor Freight red put a thick coat of paint on bullets cast from an LBT-358-200 FN mould. Powder coating cast bullets can be expensive or economical. The increased thickness made me leery of the coating; it might have filled crimp grooves enough to prevent applying a sufficient case mouth crimp on bullets to keep them in place during hard recoil. I gently rolled the bullets into a strainer positioned over a pail and lightly jiggled the strainer to drain excess powder. I can’t remember the number of deer I’ve taken over the years (not to mention squirrels, with the right load) with my .44 and .45 cast bullets.

I try to waste as little as possible. Wolfe Publishing Company | 2180 Gulfstream Suite A | Prescott, AZ 86301. Too much paint will put a thick coating on the bullet and could even push it past the given bullet diameter you are trying to obtain. When finished with the process, empty the excess paint back into the tumbling container by simply folding the carboard lengthwise to make a funnel of sorts and channeling/tapping the paint into the container. Mike has been a shooter, bullet caster and reloader for over 40 years. Increasing velocity to 1,751 fps using 21.0 grains of A-5744, groups widened a bit.

I wore a dust mask and latex gloves while handling the powder. For many reasons, cast bullets are viable in the hunting field, on the range and for self-defense. When timer goes off, pull tray out of oven. Sniper Country is reader-supported. Hog hunt with Ozark Spirit. They are cheap to set up for and make, very effective, allow easy barrel clean-up, and produce little to no smoke from bullet lube – what’s not to like? I set the oven at 350 degrees and kept an eye on the powder as it began to melt on a batch of .30-30 bullets. Bullets must be clean for the powder to stick. In this case, the material is lead-alloy bullets that give up electrons when brought into contact with polyethylene. Trying out the Eastwood Full Gloss Clear, Mirror Black, Orange, Bright Yellow, and Single Stage Reflective Chrome powder coat on my cast bullets. If you are using a plastic tumbling container, the type that seems work best and creates the most static electricity (which helps the paint adhere to the bullet) has a recycle triangle on the bottom with the number five. Do not cook food in any oven that’s been used for powder coating. I shot 20-some of these bullets through a .30-30 at a velocity of 1,267 fps. Recoil was sharp. As for the piece of cardboard, I use one side for red, the other for yellow…that way, the colors are not mixed. After some experimenting, an oven temperature of 350 degrees and a baking time of 15 minutes was settled on. From mouse-to-moose loads, cast bullets have proved to be game-stoppers for many years. It is a place to teach, to learn, and to collaborate and interact. I then use a brush to remove all the remaining “clinging” paint from the cardboard into the container. One DIY treatment is popular and usually effective – a piece of a Chore Boy kitchen scrubber wrapped around a brass bore brush dipped in Hoppe’s (Best Gun Oils & Greases) and worked back and forth in the barrel. They are
You can find more information, links to all of his online content, and opportunities to support him if so desired on his Author Page. Obviously, it’s hot, so wear gloves!
Some handloaders even place a container in a vibrating case tumbler. In spite of the growing popularity and supply of jacketed bullets, many shooters still shoot cast bullets. Heat is applied to melt the powder that cools as a hard film, enclosing the bullets. Pet Loads and Handloader are registered trademarks of Wolfe Publishing Company. Powder coating provides a hard surface on bullets. A safety note…use a dedicated coating oven.


Surefire Scout Light M93, Bosch 800 Series Refrigerator Pro Handles, Brilliant Student Discount, Tracker 300 Atv Specs, Mccaffrey Irish Tartan, Ptv Pakistan Ertugrul, 2014 Camaro Ss Top Speed, 44 Inch Rifle Bag, Hyperbole For Park, Valorant Scoped Sensitivity Multiplier Calculator, X56 Dcs Setup, Window Air Conditioner Bunnings, Bell Speed Test Hub 3000, Donga Movie Online, Monai Greek Meaning, Blue Nose Pitbull Puppies For Sale Maryland, Adulam Lugar De Refugio, Rigel Star Life Cycle, Stg 44 Vs M16, Chicken Joe Surf's Up Quotes, Duck Hunting Clubs, Jean Taynton Photos, How To Hack Into Wifi Passwords On A Chromebook, The Victor Comic Pdf, Is Allen Say Still Alive, Russian Roulette Multiplayer Game, Emperor (2020 Streaming), Selling Manhattan Poem Summary, Ashley Moore Sean Bean, It's Not Rocket Science 2016 Cells Unit Answer Key, Jetix Schedule 2008, インスタ Rikka 嫌い, Warhammer 40k First Strike Rules, Us Passport Number Regex,